Swissbit Trial Temperatur E

Read disturb ma nagement (refresh data when flash of ten read) High reliability o Best available SLC NAND Flash technology o Designed for embedde d market o MTBF 2,500,000 hour s o Data reliability: -recov erable error per 10 14 bits read o Number of connector i nsertionsremovals: 10,00 0 High performance o Up to 300MBs bur st transfer rate in SATA II - 3.0Gb sec o Sustained Write performa nce: up to 1 00MBs (4channel) o Sustained Read Performa nce: up to 1 30MBs (4channel) Available densities o 2GByte up to 64 GByte (SLC NAND Flash) 2 Temperature ranges o Commercial Temperat ure range 0 70C o Industrial Temperatur e range - 40 85C Life Cycle Management Controlled BOM RoHS compatible.

Revision: 0.90 Industriestrasse 4 CH -9552 Bronschhofe n w w w.s w i s s bi t.c o m F-240datasheet CA-HxBVRev090 Switzerland i n d ust ri al s w i s s bi t.c o m Page 6 of 55 4 Product S pecifica tion Th e CFAST TM card is a small for m factor non-volati le memory drive whic h provides hig h capacity data stora ge.

It has a standard CFAST co nnector with SATA an d powercontrol part.

T he card works at a sup ply voltage of 3.3V.

The drive with the SATA interface operates in Mode 2.

Gb s burst). With an adapter (e.g.

Swissbit CFAST Adapter ) the dr ive behaves as a standard SATA disk drive.

The adapter can be mou nted in Swissbit 2.5 S SD housing.

Swissbit Code Er Ror

The drive has an i nternal in telligent contro ller which manages interface protocol s, data stora ge and retrieval as well as hardware BCH-code Er ror Correctio n Code (ECC), defect handling, d iagnostics a nd clock contro l.

The wear leveling mechanism assures an equal usage of the Flash memor y cells to extend the life ti me.

The specification ha s been realized and approve d by the ATAATAPI-8 spec ification.

Related Documenta tion CFAST specification 1.

Serial ATA International Organization: Serial ATA Rev ision 2.6 ( w w w.

Serial Transport Protoc ols and Phys ical Interconnect (A TAATAPI-8 to ATAATAP I-5) ( w w w.

Electronic Industries Allia nce ( w w w.

Physical description The CFAST TM card contains a flash controller and Fla sh memory modu les.

The controller interface s with a hos t system allowing data to be written to and read from the Flash memor y modules.

The CFAST TM card is offered i n a Compact Flash size pac kage with a standard C FAST connector with a 7 -pin SATA connector and a 17 -pin power and control connector with 15 pin s.

Figure 6 and Figure 7 show CFAST TM card dimensions and co nnector location.

All values refer to Toshiba Flash chips in UDMA5 mode (SATA 3.0Gbits) with Sequential writeread test (256 sectors multiple commands) and sequential and ra ndom writerea d test (8 sectors multiple comman ds).Sustained Speed depends on flash type and number, filecluster size, and burst spee d.

The typical random write speed values are really random access across the whole drive.

Revision: 0.90 Industriestrasse 4 CH -9552 Bronschhofe n w w w.s w i s s bi t.c o m F-240datasheet CA-HxBVRev090 Switzerland i n d ust ri al s w i s s bi t.c o m Page 8 of 55 4.3 Environmental Specification s 4.3.1 Recommended Operating Conditions Table 3: Recommended Operating Cond itions Parameter Value Commercial Operating Temperature 0C to 70C Industrial Operating Temperature -40C to 85C Power Supply VCC Voltage 3.3V 10 Table 4: Current consump tion (1) Current Consumption (type) 3.3V Unit Read (typmax) 170200 mA Write (typmax) 180200 Idle Mode (typmax) 85100 PHYSLP mode 1.

Revision: 0.90 Industriestrasse 4 CH -9552 Bronschhofe n w w w.s w i s s bi t.c o m F-240datasheet CA-HxBVRev090 Switzerland i n d ust ri al s w i s s bi t.c o m Page 9 of 55 5 Elec trical in terf ace 5.1 Electrical d escription The CFAST CARD i s connected with a sta ndard 7 pin SAT A connector and a standar d 15 pin SATA powe r connector.

Table 10: Pin Assignment, n ame, and description Pin Signal Name Description S1 SGround Signal Ground S2 A Differential Device Receive signal S3 A- - Differential Device Receive signal S4 SGround Signal Ground S5 B- - Differential Device Transmit signal S6 B Differential Device Transmit signal S7 SGround Signal Ground PC1 CDI ) Card detect in PC2 Ground Power Ground P C3 P C6 TBD not used PC7 Ground Power Ground PC8 LED1 LED output for device activity (driven low) PC9 LED2 LED output for SATA link indication (driven low) PC10 IO1 WP Write protect input (low active) P C11 P C12 IO2 3 not used P C13PC14 3.3V Device power 3.3V PC15PC16 Ground Power Ground PC17 CDO ) Card detect out ) CDI This pin is connected to CDO and to t he card controller.

If CDI is not driven by the host, it should be connected to GND (see section 5.4 ) It can be used for PHY SLP functionality (see sectio n 5.4 ) Bot tom s ide Top s ide.

Revision: 0.90 Industriestrasse 4 CH -9552 Bronschhofe n w w w.s w i s s bi t.c o m F-240datasheet CA-HxBVRev090 Switzerland i n d ust ri al s w i s s bi t.c o m Page 10 of 55 5.2 Electrical Sp ecification Table 11 and Table 12 define the DC Characte ristics of t he CFAST card.

Swissbit Series W Ith

Unless otherwise stated, conditions are: Vcc 3.3V 5 0C to 70 C The current is measur ed by connecting a n amp meter in series w ith the V cc supply.

The meter should be set to the 2A scale range, and have a fast current pro be with an RC filter with a time constant o f 0.1ms.

Current measurements are tak en while looping on a data tran sfer command with a sec tor count of 128.

Current consumption values for both read and write com mands are not to e xceed the Maximum A verage RMS Curren t specified in Table 12.

LED2 is the SATA link i ndicator and is driven low, if the SATA is co nnected and active.

So t his pin can be tie d low by the host without accidental current through these pins.

Swissbit Driver